ASTM STANDARDS COMPARISON

ASTM D638 vs ASTM D882: Rigid Plastic vs Thin Film Tensile Testing

Compare ASTM D638 tensile testing for molded, machined, or thicker plastic specimens with ASTM D882 tensile testing for plastic film and thin sheeting. Both methods evaluate how plastics respond to pulling forces, but they use different specimen geometries, gripping approaches, strain measurement practices, and thickness ranges. ASTM D638 suits most rigid and semi-rigid plastics, while ASTM D882 is preferred for flexible films and sheeting below 1.0 mm. Choose the method that matches specimen form, thickness, and intended comparison data reliably.

Accredited Lab Network Fast Turnaround Strict NDA Standard

1. What Plastic Tensile Testing Measures

Run ASTM D638 for rigid or semi-rigid plastic specimens that fall outside the thin-sheet range. Run ASTM D882 for plastic film and thin sheeting under 1.0 mm thick. Match the method to the specimen form and thickness before you compare tensile values.

2. Full Comparison

Use the specimen form and thickness as the first selection filter. ASTM D882 states that thin plastic sheeting below 1.0 mm falls within its scope, while D638 covers thicker plastic specimens.

PARAMETERASTM D638ASTM D882
Primary material formMolded, machined, or cut plastic specimensThin plastic film and sheeting
Thickness focusTypically 1.0 mm or greater when D882 no longer appliesLess than 1.0 mm
Typical specimenDog-bone or specified tensile specimenParallel-sided strip
Grip challengeMaintain alignment and prevent grip damagePrevent slipping, tearing, and grip-induced failure
Primary outputsTensile strength, modulus, elongation, yield behaviorTensile strength, elongation, tensile modulus
Best fitRigid and semi-rigid plastic products and materialsPackaging films, flexible sheets, membranes, and thin polymer stock

3. Materials Covered

Both standards measure tensile response, but they target different specimen forms. Material thickness and flexibility drive the method choice.

ASTM D638-Rigid Plastic

  • Injection-molded thermoplastics such as ABS, nylon, polycarbonate, and polypropylene
  • Machined specimens from plastic sheet, plate, or molded products
  • Rigid and semi-rigid unreinforced and reinforced plastics within the method scope

ASTM D882-Thin Film Tensile Testing

  • Polyethylene and polypropylene packaging films
  • Flexible barrier films, liners, membranes, and thin polymer sheets
  • Thin plastic sheeting below 1.0 mm where strip specimens suit the material form

4. How Each Test Is Run

Both methods apply uniaxial tension with a universal testing machine. They differ most in specimen geometry, gripping, and strain measurement.

ASTM D638-Rigid Plastic

  • Prepare the specified D638 tensile specimen and measure its critical dimensions.
  • Align the specimen in tensile grips and apply load at the specified test speed.
  • Record load and extension to calculate tensile strength, modulus, elongation, and other required properties.

ASTM D882-Thin Film Tensile Testing

  • Cut a straight strip from the film or thin sheet and measure thickness and width.
  • Grip the strip without slippage or premature tearing and apply the required separation rate.
  • Record force and extension and calculate tensile properties using the specimen cross section.

5. Testing Equipment

EQUIPMENTASTM D638ASTM D882
Universal testing machineRequiredRequired
GripsTensile grips for shaped plastic specimensFilm or pneumatic grips that limit slip and damage
Extension measurementExtensometer or compliant strain measurement as requiredGrip separation, extensometer, or gage-mark displacement as allowed
Specimen preparationMold, die, or machine standard tensile specimensPrecision cutter for straight film strips

6. Applications

ASTM D638-Rigid Plastic

  • Plastic resin qualification and supplier comparison
  • Mechanical property data for molded parts and engineering plastics
  • Quality control for rigid and semi-rigid plastic formulations

ASTM D882-Thin Film Tensile Testing

  • Flexible packaging film qualification
  • Film extrusion process control and supplier comparison
  • Tensile characterization of liners, bags, membranes, and thin sheet

7. Strengths and Limitations

STANDARDSTRENGTHLIMITATION
ASTM D638Provides widely recognized tensile data for plastic materials and molded products with standardized specimen geometries.The specimen geometry and gripping approach do not represent very thin, highly flexible film well.
ASTM D882Targets the handling and deformation behavior of thin plastic film and sheeting and supports film-specific quality control.Thin films can show strong sensitivity to thickness variation, defects, grip pressure, orientation, and test speed.

8. Which Standard Should You Run?

IF THIS DESCRIBES YOURUN THISWHY
Your sample is a molded part, plaque, rigid sheet, or thicker plastic specimenASTM D638D638 matches the specimen form and the standard tensile geometry used for general plastics.
Your sample is flexible film or thin plastic sheeting below 1.0 mmASTM D882D882 directly addresses thin plastic film and sheet specimens and their gripping behavior.
You need to compare film data with a thicker molded plastic datasetRun each material to its applicable standardUsing the correct method preserves valid data. Do not treat values from different specimen forms as directly interchangeable.

Still unsure? Infinita Lab can review your material, specimen form, governing specification, and reporting goal before you submit samples for ASTM D638 or ASTM D882 testing. Talk to our team.

9. Frequently Asked Questions

Can I test plastic film to ASTM D638?

Use D882 when the material falls within the thin-sheet scope. D638 does not provide the preferred specimen and gripping framework for thin flexible film.

Can I compare tensile strength from D638 and D882 directly?

Use caution. Material form, thickness, specimen geometry, strain rate, and gripping can change the measured response. Compare results only when the test basis supports the comparison.

What thickness points to ASTM D882?

ASTM D882 covers thin plastic sheeting less than 1.0 mm thick. Confirm the governing material specification before testing.

Do both methods report elongation?

Yes. Both can report elongation, but the extension measurement method and specimen behavior differ, so the test report should identify the method and measurement approach.

Standard / PageDescription
ASTM D412 Tensile Stress-Strain & Set Testing for Vulcanized RubberTension Testing of Rubber and Thermoplastic Elastomers
THE SUPERLAB ADVANTAGE

Talk to a Scientist, Not a Coordinator

✓ 2,000+ Accredited Labs ✓ 20,000+ Test Types ✓ Strict NDA Standard
Home / / ASTM D638 vs ASTM D882: Rigid Plastic vs Thin Film Tensile Testing
×

Talk to an Expert

    Connect Instantly

    (888) 878-3090
    Ensure Quality with the Widest Network of Accredited Labs
    • ddd
      Quick Turnaround and Hasslefree process
    • ddd
      Confidentiality Guarantee
    • ddd
      Free, No-obligation Consultation
    • ddd
      100% Customer Satisfaction

      ddd

      Start Material Testing