ASTM STANDARDS COMPARISON

ASTM D5748 vs ASTM D3763: Stretch Film vs High-Speed Puncture

Compare low-speed protrusion puncture testing for stretch wrap film with instrumented high-speed puncture testing for plastics.

Accredited Lab Network Fast Turnaround Strict NDA Standard

1. What Puncture Testing Measures

Run ASTM D5748 for stretch wrap film when you need maximum force, force at break, penetration distance, and energy to break under a standard low-rate protrusion puncture. Use ASTM D3763 when you need instrumented puncture behavior at higher controlled velocities across a broader range of plastic materials.

 

 

2. Full Comparison

Both methods can report puncture-related force and energy, but the loading rate, fixture, material scope, and data system differ. Use the method that matches the end-use failure mode and specification.

PARAMETERASTM D5748ASTM D3763
Primary material focusStretch wrap filmPlastics, including suitable film and sheet
Loading rateStandard low-rate punctureHigh-speed puncture over controlled velocities
Deformation stateBiaxial stretch around protrusionDynamic puncture under clamped boundary conditions
InstrumentationForce and displacement from test machineHigh-speed load and displacement sensors
Primary outputsMaximum force, break force, penetration distance, energy to breakPeak force, displacement, energy, and dynamic puncture response
Best fitStretch film end-use puncture comparisonEngineering analysis of dynamic puncture behavior

3. Materials Covered

D5748 specifically targets stretch wrap film. D3763 covers a broader set of plastic materials and dynamic puncture conditions.

ASTM D5748

  • Linear low-density polyethylene stretch film
  • Industrial and consumer stretch wrap
  • Flexible film used to contain loads around corners and protrusions

ASTM D3763

  • Rigid and semi-rigid plastic plaques
  • Plastic sheet and selected film configurations
  • Materials that need high-speed puncture force and energy data

4. How Each Test Is Run

D5748 recreates a slow protrusion-type challenge to stretch film. D3763 uses dynamic instrumentation to capture a faster puncture event.

ASTM D5748

  • Clamp the stretch film over the test opening under the prescribed condition.
  • Drive the puncture probe into the film at the specified low rate.
  • Record maximum force, break force, penetration distance, and energy to break.

ASTM D3763

  • Clamp the plastic specimen in the instrumented puncture fixture.
  • Drive the striker at the selected high test velocity while sensors record force and displacement.
  • Calculate the required peak load, energy, and puncture properties from the recorded response.

5. Testing Equipment

EQUIPMENTASTM D5748ASTM D3763
Test systemUniversal test machine or puncture fixture suited to low-rate D5748Instrumented high-speed impact system
StrikerD5748 protrusion probeD3763 puncture striker
SensorsForce and displacement from controlled machine movementHigh-speed load and displacement sensors
Data acquisitionStandard mechanical test data systemHigh-speed dynamic acquisition system

6. Applications

ASTM D5748

  • Stretch wrap film development
  • Pallet load containment film comparison
  • QC for puncture resistance against product corners and protrusions

ASTM D3763

  • Dynamic puncture characterization of plastic structures
  • Material selection for impact-prone plastic parts
  • R&D that needs force-displacement and energy curves

7. Strengths and Limitations

STANDARDSTRENGTHLIMITATION
ASTM D5748Directly targets stretch wrap film and produces puncture metrics that reflect biaxial deformation around a protrusion.The standard low loading rate does not reproduce every high-speed impact event seen in service.
ASTM D3763Provides detailed dynamic puncture data and supports velocity-dependent engineering analysis.The method requires more complex instrumentation and does not directly reproduce the low-rate stretch-film geometry of D5748.

8. Which Standard Should You Run?

IF THIS DESCRIBES YOURUN THISWHY
You need puncture resistance data for stretch wrap filmASTM D5748The method specifically targets stretch wrap film and measures protrusion puncture under biaxial deformation.
You need dynamic puncture force, displacement, and energy at high speedASTM D3763The instrumented system records the full puncture event at controlled impact velocity.
You need to understand both shipping-film puncture and dynamic impact behaviorUse D5748 for stretch-film performance and D3763 for dynamic characterizationTreat the tests as complementary because the loading rates and fixtures represent different failure modes.

Still unsure? Our lab can run both on the same batch of specimens for direct side-by-side data. Talk to our team.

9. Frequently Asked Questions

Is ASTM D5748 a falling-dart test?

No. D5748 drives a protrusion probe into stretch wrap film at a standard low rate. ASTM D1709 uses a free-falling dart for plastic film impact.

What does ASTM D5748 report?

The method determines maximum force, force at break, penetration distance, and energy to break.

Does ASTM D3763 only apply to rigid plastics?

The scope covers plastics, including films, but the specimen must suit the clamped instrumented puncture configuration.

Can I compare D5748 energy directly with D3763 energy?

Use caution. Different loading rates, striker geometries, fixtures, and specimen conditions can produce different energy values.

Standard / PageDescription
THE SUPERLAB ADVANTAGE

Talk to a Scientist, Not a Coordinator

✓ 2,000+ Accredited Labs ✓ 20,000+ Test Types ✓ Strict NDA Standard
Home / / ASTM D5748 vs ASTM D3763: Stretch Film vs High-Speed Puncture Testing
×

Talk to an Expert

    Connect Instantly

    (888) 878-3090
    Ensure Quality with the Widest Network of Accredited Labs
    • ddd
      Quick Turnaround and Hasslefree process
    • ddd
      Confidentiality Guarantee
    • ddd
      Free, No-obligation Consultation
    • ddd
      100% Customer Satisfaction

      ddd

      Start Material Testing